Fluke MET/CAL Procedure ============================================================================= INSTRUMENT: Soltec 1243: (1 year) CAL VER /5520 DATE: 10-Sep-97 AUTHOR: Fluke Corporation REVISION: $Revision: 1.1 $ ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 14 NUMBER OF LINES: 226 CONFIGURATION: Fluke 5500A CONFIGURATION: Fluke 5520A ============================================================================= # # Compatibility: # 5500/CAL 4.23 or MET/CAL 4.23 or later. # # Subprocedures: # Sub Soltec 1243 DC Voltage Unit: (1 yr) CAL VER /5520 # Sub Soltec 1243 RTD Input Unit: (1 yr) CAL VER /5520 # Sub Soltec 1243 Thermocouple Unit: (1 yr) CAL VER /5520 # # Required Files: None # # System Specifications: # TUR calculation is based on specification interval of the accuracy file. # The default 5520A accuracy file contains 90 day specs. # # Fluke makes no warranty, expressed or implied, as to the fitness # or suitability of this procedure in the customer's application. # STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 ASK- P F V 1.002 ASK+ K X 1.003 HEAD PRELIMINARY INSTRUCTIONS 1.004 DISP Connect UUT to AC power and turn unit ON. 1.004 DISP 1.004 DISP Warm-up time: 30min - REQUIRED 1.004 DISP Temperature: 23 +/-2 degC 1.004 DISP Humidity: 55 +/-10% 1.005 DISP [32] WARNING 1.005 DISP HIGH VOLTAGE is used or exposed during the performance 1.005 DISP of this calibration. DEATH ON CONTACT may result if 1.005 DISP personnel fail to observe safety precautions. 1.006 DISP This procedure REQUIRES at least one plug-in unit. 1.006 DISP 1.006 DISP Install the plug-in(s) into the 1243. 1.007 HEAD {PEN LIFT} 1.008 SET SPEED : 10mm/min 1.008 SET DRIVE : OFF 1.009 MESS One at a time set the PEN LIFT switchs down & up. 1.009 MESS 1.009 MESS Check that each PEN LIFT switch works correctly. 1.009 MESS 1.010 EVAL Do {ALL PEN LIFT switches work correctly}? 2.001 HEAD {POSITION CONTROL} 2.002 SET PEN LIFT : down for all channels. 2.003 MESS For all plug-ins: 2.003 MESS 2.003 MESS Rotate the plug-in POSITION control(s) from end to end. 2.003 MESS 2.004 EVAL Do {the POSITION controls allow full scale settings}? 3.001 MESS 3.002 HEAD {CHART SPEED} 3.003 DISP Connect the 5520A to the UUT as follows: 3.003 DISP [32] 5520A NORMAL HI to Plug-in + input 3.003 DISP [32] 5520A NORMAL LO to Plug-in - input 3.004 MEM2 Enter the plug-in type (DCV, TC, or RTD). 3.005 JMPL CHART_SPEED_DCV_PLUG_IN ZCMPI(MEM2, "DCV") 3.006 JMPL CHART_SPEED_TC_PLUG_IN ZCMPI(MEM2, "TC") 3.007 JMPL CHART_SPEED_RTD_PLUG_IN ZCMPI(MEM2, "RTD") 3.008 OPBR NOTE The mainframe can only be tested using either the 3.008 OPBR DCV or THERMOCOUPLE plug-in. You may continue testing 3.008 OPBR the mainframe by selecting a different plug-in or you 3.008 OPBR may skip the mainframe test and verify the RTD plug-in 3.008 OPBR at this time. 3.008 OPBR 3.008 OPBR Would you like to skip the mainframe test and proceed 3.008 OPBR with the RTD verification? 3.009 JMPF 3.004 3.010 RSLT =Not tested 3.011 JMPL CHART_SPEED_RTD_PLUG_IN 3.012 LABEL CHART_SPEED_DCV_PLUG_IN 3.013 SET RANGE : 10mV 3.014 JMP 3.021 3.015 LABEL CHART_SPEED_TC_PLUG_IN 3.016 SET RANGE : MIDDLE RANGE 3.017 JMP 3.021 3.018 LABEL CHART_SPEED_RTD_PLUG_IN 3.019 HEAD {CHART SPEED} 3.020 HEAD CHART SPEED: {60mm/hr} 3.021 SET SPEED : 60mm/hr 3.021 SET DRIVE : ON 3.022 M550 1.5mVoff 3.023 5520 0.01H 3mV SQ S 2W 3.024 EVAL Is there 1 cycle every 1.5mm (.01Hz) 4.001 HEAD CHART SPEED: {60cm/hr} 4.002 SET SPEED : 60cm/hr 4.003 5520 0.01H 3mV SQ S 2W 4.004 EVAL Is there 1 cycle every 1.5cm (.01Hz) 5.001 HEAD CHART SPEED: {60mm/min} 5.002 SET SPEED : 60mm/min 5.003 5520 0.1H 3mV SQ S 2W 5.004 EVAL Is there 1 cycle every 10mm (.1Hz) 6.001 HEAD CHART SPEED: {60cm/min} 6.002 SET SPEED : 60cm/min 6.003 5520 0.1H 3mV SQ S 2W 6.004 EVAL Is there 1 cycle every 10cm (.1Hz) 7.001 HEAD CHART SPEED: {40cm/min} 7.002 SET SPEED : 40cm/min 7.003 5520 0.1H 3mV SQ S 2W 7.004 EVAL Is there 1 cycle every 6.66cm (.1Hz) 8.001 HEAD CHART SPEED: {30cm/min} 8.002 SET SPEED : 30cm/min 8.003 5520 0.1H 3mV SQ S 2W 8.004 EVAL Is there 1 cycle every 5cm (.1Hz) 9.001 HEAD CHART SPEED: {20cm/min} 9.002 SET SPEED : 20cm/min 9.003 5520 0.1H 3mV SQ S 2W 9.004 EVAL Is there 1 cycle every 3.33cm (.1Hz) 10.001 HEAD CHART SPEED: {5cm/min} 10.002 SET SPEED : 15cm/min 10.003 5520 0.1H 3mV SQ S 2W 10.004 EVAL Is there 1 cycle every 2.5cm (.1Hz) 11.001 HEAD CHART SPEED: {1cm/min} 11.002 SET SPEED : 10cm/min 11.003 5520 0.1H 3mV SQ S 2W 11.004 EVAL Is there {ONE cycle every 1.66cm (.1Hz)} 12.001 M550 * 12.002 SET DRIVE : OFF 12.003 OPBR Verification of the MAINFRAME is complete. 12.003 OPBR 12.003 OPBR Would you like to test the PLUG-IN UNITS? 12.004 JMPL END 12.005 HEAD {LEFT CHANNEL PLUG-IN} 12.006 OPBR Is there a plug-in in the left channel? 12.007 JMPT 12.010 12.008 RSLT =Not installed 12.009 JMPL CENTER_CHANNEL_PLUG_IN 12.010 MEM2 Enter the plug-in type (DCV, TC, or RTD). 12.011 JMPL LEFT_CHANNEL_DCV_PLUG_IN ZCMPI(MEM2, "DCV") 12.012 JMPL LEFT_CHANNEL_TC_PLUG_IN ZCMPI(MEM2, "TC") 12.013 JMPL LEFT_CHANNEL_RTD_PLUG_IN ZCMPI(MEM2, "RTD") 12.014 DISP Unknown plug-in type! 12.015 JMP 12.010 12.016 LABEL LEFT_CHANNEL_DCV_PLUG_IN 12.017 RSLT =DCV PLUG-IN 12.018 CALL Sub Soltec 1243 DC Voltage Unit (1 yr) CAL VER /5520 12.019 JMPL CENTER_CHANNEL_PLUG_IN 12.020 LABEL LEFT_CHANNEL_TC_PLUG_IN 12.021 RSLT =THERMOCOUPLE PLUG-IN 12.022 CALL Sub Soltec 1243 Thermocouple Unit (1 yr) CAL VER /5520 12.023 JMPL CENTER_CHANNEL_PLUG_IN 12.024 LABEL LEFT_CHANNEL_RTD_PLUG_IN 12.025 RSLT =RTD PLUG-IN 12.026 CALL Sub Soltec 1243 RTD Input Unit (1 yr) CAL VER /5520 12.027 JMPL CENTER_CHANNEL_PLUG_IN 12.028 EVAL Dummy 13.001 LABEL CENTER_CHANNEL_PLUG_IN 13.002 HEAD {CENTER CHANNEL PLUG-IN} 13.003 OPBR Is there a plug-in in the center channel? 13.004 JMPT 13.007 13.005 RSLT =Not installed 13.006 JMPL RIGHT_CHANNEL_PLUG_IN 13.007 MEM2 Enter the plug-in type (DCV, TC, or RTD). 13.008 JMPL CENTER_CHANNEL_DCV_PLUG_IN ZCMPI(MEM2, "DCV") 13.009 JMPL CENTER_CHANNEL_TC_PLUG_IN ZCMPI(MEM2, "TC") 13.010 JMPL CENTER_CHANNEL_RTD_PLUG_IN ZCMPI(MEM2, "RTD") 13.011 DISP Unknown plug-in type! 13.012 JMP 13.007 13.013 LABEL CENTER_CHANNEL_DCV_PLUG_IN 13.014 RSLT =DCV PLUG-IN 13.015 CALL Sub Soltec 1243 DC Voltage Unit (1 yr) CAL VER /5520 13.016 JMPL RIGHT_CHANNEL_PLUG_IN 13.017 LABEL CENTER_CHANNEL_TC_PLUG_IN 13.018 RSLT =THERMOCOUPLE PLUG-IN 13.019 CALL Sub Soltec 1243 Thermocouple Unit (1 yr) CAL VER /5520 13.020 JMPL RIGHT_CHANNEL_PLUG_IN 13.021 LABEL CENTER_CHANNEL_RTD_PLUG_IN 13.022 RSLT =RTD PLUG-IN 13.023 CALL Sub Soltec 1243 RTD Input Unit (1 yr) CAL VER /5520 13.024 JMPL RIGHT_CHANNEL_PLUG_IN 13.025 EVAL Dummy 14.001 LABEL RIGHT_CHANNEL_PLUG_IN 14.002 HEAD {RIGHT CHANNEL PLUG-IN} 14.003 OPBR Is there a plug-in in the RIGHT channel? 14.004 JMPT 14.007 14.005 RSLT =Not installed. 14.006 JMPL END 14.007 MEM2 Enter the plug-in type (DCV, TC, or RTD). 14.008 JMPL RIGHT_CHANNEL_DCV_PLUG_IN ZCMPI(MEM2, "DCV") 14.009 JMPL RIGHT_CHANNEL_TC_PLUG_IN ZCMPI(MEM2, "TC") 14.010 JMPL RIGHT_CHANNEL_RTD_PLUG_IN ZCMPI(MEM2, "RTD") 14.011 DISP Unknown plug-in type! 14.012 JMP 14.007 14.013 LABEL RIGHT_CHANNEL_DCV_PLUG_IN 14.014 RSLT =DCV PLUG-IN 14.015 CALL Sub Soltec 1243 DC Voltage Unit (1 yr) CAL VER /5520 14.016 JMPL END 14.017 LABEL RIGHT_CHANNEL_TC_PLUG_IN 14.018 RSLT =THERMOCOUPLE PLUG-IN 14.019 CALL Sub Soltec 1243 Thermocouple Unit (1 yr) CAL VER /5520 14.020 JMPL END 14.021 LABEL RIGHT_CHANNEL_RTD_PLUG_IN 14.022 RSLT =RTD PLUG-IN 14.023 CALL Sub Soltec 1243 RTD Input Unit (1 yr) CAL VER /5520 14.024 LABEL END 14.025 END